MVME162-026A工控模塊機器人備件
這使您可以將連接器調整到最佳位置，以保護連接免受可能的環境污染，同時提供電纜接入。圓形連接器外殼可沿任一方向旋轉。按照以下步驟旋轉連接器。在反饋或動力制動接頭上安裝并完全固定配合電纜。用手抓住配合的連接器和電纜插頭，并將其緩慢旋轉至電機外部。對另一個接頭重復這些步驟。注意如果通電，未安裝的電機斷開的機械聯軸器松脫的軸鍵和斷開的電纜是危險的。鎖定并標記拆卸的設備限制電源。向電機通電前，取下軸鍵和其他可能從軸上拋出的機械聯軸器。注意確保電纜已安裝并受到約束，以防止電纜連接處的不均勻張力或彎曲。當電纜彎曲時，電纜上過大且不均勻的橫向力會抑制環境密封。注意連接器設計為在電機安裝期間旋轉到固定位置，并保持在該位置，無需進一步調整。不要多次旋轉連接器，也不要使用工具或過度用力旋轉連接器。過度旋轉或用力會損壞連接器密封，降低電機的國際防護等級，如第頁規范所述。注意僅對電機連接器和電纜插頭施加力。不要對從電纜插頭伸出的電纜施加力。不要使用工具例如鉗子和虎鉗旋轉連接器。系列或更小框架尺寸的低慣量無刷伺服電機自動化年月安裝電機按照以下步驟安裝電機。為電機提供足夠的間隙散熱片和氣流，使其保持在的工作溫度范圍內。除非強制冷卻空氣穿過電機，否則不要封閉電機，并使其他發熱設備遠離電機。散熱器要求在第頁規范的腳注中列出。驗證應用的軸向和徑向軸負載不超過第頁電機負載力額定值中列出的值。將電機與電纜連接放置在電機下方。有關正確電機和電纜定位的視覺參考，請參閱第頁的拆卸軸蓋。正確安裝和對齊電機電機包括一個安裝導向器，用于在機器上對齊電機。當軸鍵與連接器對齊時，線編碼器上出現索引脈沖。
This allows you to adjust the connector to the optimal position to protect the connection from possible environmental pollution while providing cable access. The circular connector housing can be rotated in either direction. Follow these steps to rotate the connector. Install and fully secure the mating cable on the feedback or power brake connector. Grasp the mating connector and cable plug by hand and slowly rotate them to the outside of the motor. Repeat these steps for the other connector. Note that if the motor is powered on, the loose shaft keys and the disconnected cables of the disconnected mechanical coupling of the unmounted motor are dangerous. Lock and mark the removed device to limit power supply. Before energizing the motor, remove the shaft key and other mechanical couplings that may be thrown from the shaft. Care shall be taken to ensure that cables are installed and restrained to prevent uneven tension or bending at cable connections. When the cable is bent, excessive and uneven lateral forces on the cable will inhibit environmental sealing. Note that the connector is designed to rotate to a fixed position during motor installation and remain in that position without further adjustment. Do not rotate the connector more than once, nor use tools or excessive force to rotate the connector. Excessive rotation or force can damage the connector seal and reduce the international protection level of the motor, as described in the specifications on page. Note that only force is applied to the motor connector and cable plug. Do not apply force to the cable protruding from the cable plug. Do not use tools such as pliers and vises to rotate the connector. Automatic installation of low inertia brushless servo motor with frame size of series or smaller The motor shall be installed according to the following steps. Provide the motor with enough clearance, radiator and air flow to keep it within the operating temperature range of. Do not close the motor and keep other heating equipment away from the motor unless forced cooling air passes through the motor. The radiator requirements are listed in the footnote to the specification on page. Verify that the applied axial and radial shaft loads do not exceed the values listed in Motor Load Force Ratings on page. Place the motor and cable connection under the motor. For a visual reference to correct motor and cable positioning, refer to Removing the Shaft Cover on page. Proper mounting and alignment of the motor The motor includes a mounting guide for aligning the motor on the machine. When the axis key is aligned with the connector, the index pulse appears on the wire encoder.
