MVME162-023A自動化模塊備件
確保皮帶負載在電機限制范圍內，并且所有皮帶和滑輪正確對齊。遵循齒輪箱滑輪或其他電機附件的制造商建議。注意如果在安裝聯軸器和皮帶輪期間對軸施加劇烈沖擊，可能會損壞電機軸承和反饋裝置。在安裝或拆卸過程中，不要用工具敲擊聯軸器或皮帶輪。注意電機的外表面在運行過程中可能會達到的高溫。采取預防措施，防止意外接觸熱表面。選擇電機配合連接和電纜時，應考慮電機表面溫度。系列或更小框架尺寸的低慣量無刷伺服電機自動化年月連接電機電纜安裝電機后，按照以下步驟連接反饋和動力制動電纜。如果使用螺紋電纜插頭，安裝形圈。接頭上的形圈是實現最大環境等級所必需的。如果使用電纜插頭，請勿安裝形圈。在電纜中形成滴水環見第頁。注意在將電纜連接或斷開電機之前，必須關閉伺服驅動電源，如果電纜在電機端斷開，也必須關閉。如果在伺服驅動器通電時連接或斷開饋線電源或制動電纜，可能會發生電弧或意外運動。注意確保電纜已安裝并受到約束，以防止電纜連接器處的不均勻張力或彎曲。在整個電纜敷設過程中，每隔米英尺提供支撐。電纜連接器處的橫向力過大且不均勻當電纜彎曲或電線在電纜壓蓋處分離時，導致連接器的環境密封打開和關閉。電機連接器不要在電機連接器上安裝形圈螺紋電纜插頭標準反饋和電源電纜連續撓性饋電和動力制動電纜使用螺紋電纜插頭時，請在馬達連接器上安裝形圈。確認形圈沒有損壞，沒有扭曲，并位于接頭后部附近的凹槽中。電纜插頭預留槽使用電纜插頭時，請勿在就緒電機連接器上安裝形圈。電纜插頭標準和連續撓性反饋電纜標準以及連續撓性動力制動電纜就緒電機連接器系列低慣量無刷伺服電機，具有或更小的框架尺寸自動化年月日。
Make sure that the belt load is within the limits of the motor and that all belts and pulleys are correctly aligned. Follow the manufacturer's recommendations for gearbox pulleys or other motor accessories. Note that if severe impact is applied to the shaft during the installation of the coupling and pulley, the motor bearing and feedback device may be damaged. Do not knock the coupling or pulley with tools during installation or removal. Pay attention to the high temperature that the outer surface of the motor may reach during operation. Take precautions to prevent accidental contact with hot surfaces. The motor surface temperature shall be considered when selecting the motor mating connection and cable. Automation of low inertia brushless servo motor of series or smaller frame size Connect the motor cable. After installing the motor, connect the feedback and power brake cables according to the following steps. If a threaded cable plug is used, install the O-ring. The O-rings on the connector are necessary to achieve the maximum environmental rating. If a cable plug is used, do not install the O-ring. Form a drip loop in the cable, see page. Note that before connecting or disconnecting the cable to the motor, the servo drive power must be turned off. If the cable is disconnected at the motor end, it must also be turned off. If the feeder power supply or brake cable is connected or disconnected when the servo drive is powered on, arcing or unexpected movement may occur. Take care to ensure that the cable is installed and restrained to prevent uneven tension or bending at the cable connector. Support shall be provided every meter foot throughout the cable laying process. The lateral force at the cable connector is too large and uneven. When the cable is bent or the wires are separated in the cable gland, the environmental seal of the connector is opened and closed. Motor connector Do not install ring screw cable plug on motor connector Standard feedback and power cable Continuous flexible feeding and power brake cable When using screw cable plug, please install ring on motor connector. Verify that the O-ring is not damaged, twisted, and located in the groove near the rear of the connector. When using the cable plug in the cable plug preparation slot, do not install the O-ring on the ready motor connector. Cable plug standard and continuous flexible feedback cable standard as well as continuous flexible power brake cable ready motor connector series low inertia brushless servo motor, with or less frame size automation date.
