MVME162-022A工控機器人備件
小心地將反饋或動力制動電纜插頭如圖所示上的平面與電機接頭上的平面對齊。用手擰緊插頭上的套環，使其完全固定在連接器上螺紋電纜插頭需要旋轉五到六圈。電纜插頭需要大約四分之一轉。將電纜插頭與電機接頭配合時，不要用力過猛。如果插頭和連接器不能用輕微的手用力連接在一起，請重新對齊平面并重試。重要事項所示電機方向用于清楚顯示每個電纜插座上的對準標記。安裝時建議的電機方向?qū)⒔宇^定位在電機底部。提示完全固定的螺紋插頭在連接器和插頭之間留下約的小開口。注意對齊鍵控連接器并手動擰緊建議的圈數。如果無法擰緊連接器，請驗證鍵控連接器是否正確對齊。不要使用工具例如鉗子和虎鉗擰緊接頭。制動器和電源連接器反饋連接器對齊平面對齊平面系列或更小框架尺寸的低慣量無刷伺服電機自動化年月產品尺寸本節提供了電機的尺寸。見詳圖±±軸直徑公差電機，電機?詳圖軸直徑和電機?連接器反饋連接器直徑螺栓圓上的直徑孔尺寸單位為軸端螺紋孔電機螺紋螺紋深度，電機螺紋螺紋深度連接器外殼可在導向直徑公差范圍內旋轉電機?電機，鍵系列低慣量無刷伺服電機，框架尺寸為或更小自動化年月和電機尺寸電機設計為公制尺寸。英寸尺寸是毫米的近似換算。無公差的尺寸僅供參考。電機類別。編號如果訂購帶制動器的或電機，則在尺寸和上增加在和上增加如果訂購帶制動器的或電機，則尺寸和增加和增加此尺寸的公差為±±鍵槽軸直徑和導向直徑公差見第頁。。毫米英寸毫米英寸。系列或更小框架尺寸的低慣量無刷伺服電機自動化年月公差和補充尺寸電機負載力額定值電機能夠在持續軸負載下運行。圖中顯示了徑向和軸向負載力的位置，并列出了最大值。載荷以磅千克為單位進行測量，這是數學轉換。軸上的負載力下表表示了各種負載和速度下的小時軸承疲勞壽命。這小時的使用壽命沒有考慮到因外部來源的軸承潤滑脂污染而可能導致的特定應用壽命減少。和鍵槽公差軸跳動導向偏心度最大端面跳動鍵槽深度鍵槽寬度徑向負載力額定值電機類別。
Carefully align the plane on the feedback or power brake cable plug as shown in the figure with the plane on the motor connector. Tighten the collar on the plug by hand to fully secure it to the connector The threaded cable plug needs to be rotated five to six turns. The cable plug takes about a quarter turn. Do not use excessive force when fitting the cable plug with the motor connector. If the plug and connector cannot be connected together with slight hand force, realign the plane and try again. IMPORTANT The motor orientation shown is used to clearly show the alignment marks on each cable socket. The recommended motor direction during installation locates the connector at the bottom of the motor. Prompt that a fully secured threaded plug leaves approximately a small opening between the connector and the plug. Note the alignment of the keyed connector and hand tighten the recommended number of turns. If the connector cannot be tightened, verify that the keyed connector is properly aligned. Do not use tools such as pliers and vises to tighten the connector. Brake and power connector feedback connector alignment plane alignment plane series or lower frame size low inertia brushless servo motor automation monthly product size This section provides motor dimensions. See detail drawing ± ± shaft diameter tolerance motor, motor detail drawing shaft diameter and motor connector feedback connector diameter Diameter hole size on bolt circle Unit: shaft end threaded hole Motor thread depth, motor thread thread depth Connector housing can rotate motor motor within the guide diameter tolerance, key series low inertia brushless servo motor, The frame size is or smaller, and the motor size is designed as metric size. Inch dimensions are approximate conversions of millimeters. Dimensions without tolerances are for reference only. Motor category. No. If ordering a braked or motor, add dimensions and to add dimensions and If ordering a braked or motor, the tolerance for dimensions and adding and adding this dimension is ± ± the tolerance for keyway shaft diameter and guide diameter see page.. Millimeters inches millimeters inches. Series or smaller frame size low inertia brushless servo motor automation Monthly tolerance and supplementary size Motor load force rating The motor can operate under continuous axle load. The figure shows the location of the radial and axial load forces and lists the maximum values. The load is measured in pounds and kilograms, which is a mathematical conversion. The following table shows the hourly bearing fatigue life under various loads and speeds. The service life at this hour does not take into account the specific service life reduction that may result from contamination of bearing grease from external sources. And keyway tolerance shaft runout pilot eccentricity maximum end face runout keyway depth keyway width radial load force rating motor category.
