MVME162-021A工控備件機器人模塊
最大速度磅軸向負載力徑向負載力施加在軸延伸中心。系列或更小框架尺寸的低慣量無刷伺服電機自動化年月軸向負載力額定值最大徑向負載電機類別。編號，最大速度電機類別。轉分轉分轉分轉分，最大速度磅系列或更小框架尺寸的低慣量無刷伺服電機自動化年月連接器數據本表提供了連接器上的反饋電源和制動引腳的信號描述。反饋和引腳描述引腳高分辨率編碼器高分辨率編碼器增量編碼器引腳和相功率相位和功率相位也可以分別標記為和。相相接地數據數據保留數據數據保留保留保留保留公共公共連接器保留保留公共保留保留反饋連接器系列或更小框架尺寸的低慣量無刷伺服電機自動化年月拆除和安裝軸鍵軸鍵由鋼制成。指定的公差為安全和剛性連接提供過盈配合略大于開口。要取下軸鍵，請執行以下操作之一用鉗子或類似工具抓住鍵，將其抬起。將螺絲刀插入鑰匙和插槽之間，撬起鑰匙。要安裝軸鍵，請執行以下步驟。在繼續操作之前，確認替換鍵與軸中的鍵槽和匹配的機械連接例如，聯軸器或滑輪相匹配。將鍵的前部與電機軸的前部對齊。這可防止鍵槽電機端的弧形切割端干擾鍵的正確定位。用夾具支撐軸直徑的下側，并使用受控的按壓裝置在頂面施加恒定的力，將鍵壓入軸中。軸鍵安裝注意事項安裝或拆卸軸鍵時，不要用工具敲擊電機的軸聯軸器或滑輪。如果在安裝聯軸器和皮帶輪或拆除軸鍵時對軸施加劇烈沖擊，或者如果從電機電機上施加杠桿，則可能會損壞電機軸承和反饋裝置以拆除安裝在電機軸上的裝置。用車輪拉拔器向軸的用戶端施加恒定壓力，以移除摩擦配合或卡住的裝置。用于電機支架的鍵槽鍵軸支架的鍵對齊徑向切口系列低慣量無刷伺服電機，框架尺寸為或更小自動化年月電機電纜和附件套件本節介紹了系列低慣性電機可用的附件。電機電纜工廠制造的反饋電纜和電力電纜有標準電纜長度。
Maximum speed pounds axial load force Radial load force is applied to the shaft extension center. Series or smaller frame size low inertia brushless servo motor automation Monthly axial load force rating Maximum radial load motor category. Number, maximum speed motor category. Turn to turn, turn to turn, turn to turn, maximum speed pounds series or smaller frame size low inertia brushless servo motor automation monthly connector data This table provides the signal description of the feedback power supply and brake pin on the connector. Feedback and pin description pins High resolution encoder High resolution encoder Incremental encoder pin and phase power phase and power phase can also be marked as and respectively. Phase grounding data data retention data retention retention retention retention public public connector retention retention public retention retention feedback connector series or smaller frame size low inertia brushless servo motor automation removal and installation shaft key shaft key is made of steel. The specified tolerance provides an interference fit slightly greater than the opening for safe and rigid connections. To remove the shaft key, do one of the following to grasp the key with pliers or a similar tool and lift it. Insert a screwdriver between the key and the slot and pry up the key. To install the shaft key, perform the following steps. Before continuing, confirm that the replacement key matches the keyway in the shaft and the matching mechanical connection, such as coupling or pulley. Align the front of the key with the front of the motor shaft. This prevents the arc-shaped cutting end of the motor end of the keyway from interfering with the correct positioning of the key. Use a jig to support the lower side of the shaft diameter, and use a controlled press device to apply a constant force on the top surface to press the key into the shaft. Precautions for shaft key installation When installing or removing the shaft key, do not use tools to knock the shaft coupling or pulley of the motor. If the shaft is severely impacted when installing the coupling and pulley or removing the shaft key, or if the lever is applied from the motor, the motor bearing and feedback device may be damaged to remove the device installed on the motor shaft. Use a wheel puller to apply constant pressure to the user end of the shaft to remove friction fits or stuck devices. Keyway for motor support Keyway for key shaft support Key alignment Radial notch series low inertia brushless servo motor, frame size is or smaller Automation motor cable and accessory kit This section describes the accessories available for series low inertia motors. The feedback cable and power cable manufactured by the motor cable factory have standard cable lengths.
