ICS TRIPLEX T8220 DCS工控模塊備件
>程序管理器窗口中的“關于程序管理器”菜單項。驗證可用系統資源是否為60%或更高。如果它們較低，請關閉所有未使用的其他程序。2.Windows目錄結構中的threed.vbx文件被469PC軟件（以及可能的其他Windows）使用? 程序）。此文件的某些舊版本與469PC不兼容；因此，可能需要使用469PC附帶的最新版本更新此文件。安裝469PC軟件后，此文件將位于\GEPM\469PC\threed.vbx.3中。要更新threed.vbx文件，請找到當前使用的文件并對其進行備份，例如threed.bak.4。應進行搜索以查找本地PC硬盤上的任何三個.vbx文件。需要替換的文件位于\windows或\windows\system目錄中。5.將原始的threed.vbx替換為\GEPM\469pc\threed.vfx。確保將新文件復制到原始文件所在的目錄。6.如果Windows? 阻止替換此文件，請重新啟動電腦并在打開任何程序之前替換該文件。7.重新啟動Windows? 以使這些更改充分生效。GE Power Management 469電機管理繼電器A-1附錄A A.1調試A附錄A附錄AA.1調試A.1.1調試匯總表A–1：設定值第1–469頁設置描述默認用戶值密碼密碼----首選項默認消息周期時間2.0秒默認消息超時300秒平均電機負載計算周期15分鐘。溫度顯示攝氏度跟蹤內存觸發位置25%跟蹤內存緩沖區8 x 14周期顯示更新間隔0.4秒過濾器間隔0周期串行端口從屬地址254組件。RS485波特率9600波特補償。RS485奇偶校驗無輔助。RS485波特率9600波特輔助。RS485奇偶校驗無消息SCRATCHPAD文本1文本2文本3文本4文本5表A–2：設定值第2頁-系統設置描述默認用戶值電流感應相位CT主未編程電機滿載電流未編程接地CT多線50:0.025接地CT主100 A相位差CT無相位差CT主100 B啟用2速電機保護。無速度2相CT主100 A速度2電機FLA 1 A電壓感應VT連接類型無啟用單VT連接斷開電壓互感器比率35.00:1電機銘牌電壓4000 V電力系統標稱系統頻率60 Hz系統相序ABC速度2相序ABC串行通信控制串行通信控制。關閉分配啟動控制繼電器輔助2降低電壓降低電壓啟動關閉分配控制繼電器輔助3僅限轉換接通電流分配跳閘繼電器跳閘降低電壓啟動水平100%FLA降低電壓啟動定時器200 s A-2 469電機管理繼電器GE電源管理A.1調試附錄
> About Program Manager menu item from the Program Manager window. Verify that the available system resources are 60% or higher. If they are lower, close any other programs that are not being used. 2. The threed.vbx file in the Windows directory structure is used by the 469PC software (and possibly other Windows? programs). Some older versions of this file are not compatible with 469PC; therefore it may be necessary to update this file with the latest version included with 469PC. After installation of the 469PC software, this file will be located in \GEPM\469PC\threed.vbx. 3. To update the threed.vbx file, locate the currently used file and make a backup of it, e.g. threed.bak. 4. A search should be conducted to locate any threed.vbx files on the local PC hard drive. The file which needs replacing is the one located in the \windows or the \windows\system directory. 5. Replace the original threed.vbx with \GEPM\469pc\threed.vbx. Ensure that the new file is copied to the same directory where the original one was. 6. If Windows? prevents the replacing of this file, restart the PC and replace the file before any programs are opened. 7. Restart Windows? for these changes to take full effect. GE Power Management 469 Motor Management Relay A-1 APPENDIX A A.1 COMMISSIONING A APPENDIX A APPENDIX AA.1 COMMISSIONING A.1.1 COMMISSIONING SUMMARY Table A–1: SETPOINTS PAGE 1 – 469 SETUP DESCRIPTION DEFAULT USER VALUE PASSCODE Passcode ---- PREFERENCES Default Message Cycle Time 2.0 s Default Message Timeout 300 s Avg. Motor Load Calc. Period 15 min. Temperature Display Celsius Trace Memory Trigger Pos. 25% Trace Memory Buffers 8 x 14 cycles Display Update Interval 0.4 s Filter Interval 0 cycles SERIAL PORTS Slave Address 254 Comp. RS485 Baud Rate 9600 baud Comp. RS485 Parity None Aux. RS485 Baud Rate 9600 baud Aux. RS485 Parity None MESSAGE SCRATCHPAD Text 1 Text 2 Text 3 Text 4 Text 5 Table A–2: SETPOINTS PAGE 2 – SYSTEM SETUP DESCRIPTION DEFAULT USER VALUE CURRENT SENSING Phase CT Primary Not Programmed Motor Full Load Amps Not Programmed Ground CT Multilin 50:0.025 Ground CT Primary 100 A Phase Differential CT None Phase Differential CT Primary 100 A Enable 2-Speed Motor Prot. No Speed2 Phase CT Primary 100 A Speed2 Motor FLA 1 A VOLTAGE SENSING VT Connection Type None Enable Single VT Connection Off Voltage Transformer Ratio 35.00:1 Motor Nameplate Voltage 4000 V POWER SYSTEM Nominal System Frequency 60 Hz System Phase Sequence ABC Speed2 Phase Sequence ABC SERIAL COMMUNICATION CONTROL Serial Communication Ctrl. Off Assign Start Control Relays Auxiliary2 REDUCED VOLTAGE Reduced Voltage Starting Off Assign Control Relays Auxiliary3 Transition On Current Only Assign Trip Relays Trip Reduced Voltage Start Level 100% FLA Reduced Voltage Start Timer 200 s A-2 469 Motor Management Relay GE Power Management A.1 COMMISSIONING APPENDIX
