ICS TRIPLEX T3404模塊控制器
，則允許訪問設置點的有效密碼。1.469編程按邏輯組劃分為頁面。按下可循環瀏覽設定點頁面，直到屏幕上出現所需頁面。按下可進入頁面。2.每一頁都進一步細分為子組。按和循環瀏覽子組，直到屏幕上顯示所需的子組。按以輸入子組。3.每個子組具有一個或多個相關的設置點消息。按和循環顯示設定點消息，直到出現所需的設定點消息。4.可通過按下或直到出現所需值并按下來更改大多數設定點消息。也可以通過數字鍵（包括小數）和按鍵輸入數字設定點。如果輸入的設定值超出范圍，原始設定值將重新出現。如果輸入的設定點失步，則將存儲調整值（例如，對于步驟95、100、105存儲為100的設定點，為101）。如果輸入新值時出錯，則按下可將設定點返回到其原始值。文本編輯是第3–2頁第b）節：輸入字母數字文本中詳細描述的特殊情況。每次成功存儲新設定點時，顯示屏上將閃爍一條消息，說明“新設定點已存儲”。5.按4、6和9鍵，然后按。顯示以下閃爍信息：顯示屏返回至6。按退出子組。多次按下將始終將光標返回到頁面頂部。nn設定點nn S1 469設置n密碼n[ENTER]獲取更多輸入密碼訪問：新設定點已存儲設定點訪問：允許的設定點消息消息消息輸入消息值輸入輸入退出進入退出退出3-4 469電機管理繼電器GE Multilin 3.2 469PC軟件接口3用戶界面3 3.2469PC軟件界面3.2.1要求第章提供了安裝和/或升級469PC軟件的先前安裝、升級繼電器固件以及寫入/編輯設定點文件所需的信息。需要注意的是，469PC軟件只能用于固件版本30D220A4.000、30D220A8.000、30D251A8.000或更高版本。469PC與Mods或220之前的任何固件版本不兼容，如果編輯設置點，可能會導致錯誤。它可用于升級較舊版本的繼電器固件，但所有先前編程的設定點將被清除。在重新編程469固件之前，確保將所有設定點保存到文件中。469PC軟件必須滿足以下最低要求才能在計算機上正常運行。?處理器：最低486，建議使用奔騰或更高版本?內存：最低4 MB，建議使用16 MB，最低540 K的常規內存?硬盤：安裝軟件前需要20 MB的可用空間。?操作系統：Windows 3.1、Windows 3.11 for Workgroups、Windows NT、，
a valid passcode to allow access to setpoints if the passcode was "469". 1. The 469 programming is broken down into pages by logical groups. Press to cycle through the setpoint pages until the desired page appears on the screen. Press to enter a page. 2. Each page is broken further into subgroups. Press and to cycle through subgroups until the desired subgroup appears on the screen. Press to enter a subgroup. 3. Each sub-group has one or more associated setpoint messages. Press and to cycle through setpoint messages until the desired setpoint message appears. 4. The majority of setpoint messages may be altered by pressing or until the desired value appears and pressing . Numeric setpoints may also be entered through the numeric keys (including decimals) and pressing . If the entered setpoint is out of range, the original setpoint value reappears. If the entered setpoint is out of step, an adjusted value will be stored (e.g. 101 for a setpoint that steps 95, 100, 105 is stored as 100). If a mistake is made entering the new value, pressing returns the setpoint to its original value. Text editing is a special case described in detail in Section b): Entering Alphanumeric Text on page 3–2. Each time a new setpoint is successfully stored, a message will flash on the display stating "NEW SETPOINT HAS BEEN STORED". 5. Press the 4, 6, and 9 keys, then press . The following flash message is displayed: and the display returns to 6. Press to exit the subgroup. Pressing numerous times will always returns the cursor to the top of the page. nn SETPOINTS nn S1 469 SETUP n PASSCODE n [ENTER] for more ENTER PASSCODE FOR ACCESS: NEW SETPOINT HASE BEEN STORED SETPOINT ACCESS: PERMITTED SETPOINT MESSAGE MESSAGE MESSAGE ENTER MESSAGE MESSAGE VALUE VALUE ENTER ENTER ESCAPE ENTER ESCAPE ESCAPE 3-4 469 Motor Management Relay GE Multilin 3.2 469PC SOFTWARE INTERFACE 3 USER INTERFACES 3 3.2469PC SOFTWARE INTERFACE 3.2.1 REQUIREMENTS This chapter provides the necessary information to install and/or upgrade a previous installation of the 469PC software, upgrade the relay firmware, and write/edit setpoint files. It should be noted that the 469PC software should only be used with firmware versions 30D220A4.000, 30D220A8.000, 30D251A8.000 or later releases. 469PC is not compatible with Mods or any firmware versions prior to 220, and may cause errors if setpoints are edited. It can be used to upgrade older versions of relay firmware, but all previously programmed setpoints will be erased. Ensure that all setpoints are saved to a file before reprogramming the 469 firmware. The following minimum requirements must be met for the 469PC software to properly operate on a computer. ? Processor: minimum 486, Pentium or higher recommended ? Memory: minimum 4 MB, 16 MB recommended minimum 540 K of conventional memory ? Hard Drive: 20 MB free space required before installation of software. ? O/S: Windows 3.1, Windows 3.11 for Workgroups, Windows NT,
