ICS TRIPLEX T3160化模塊備件
通過繼電器，將顯示此消息。4.單擊“確定”以編輯通信設置（或者隨時選擇“通信”>“計算機”菜單項）。將出現“通信/計算機”對話框，其中包含本地PC的各種通信設置。應按如下所示修改設置。圖3-3：通信/計算機對話框5。要開始通信，請單擊對話框通信部分中的ON按鈕。狀態部分指示通信狀態。如果建立了通信，將顯示消息“469PC現在正在與469通話”。此外，屏幕右下角的狀態指示“正在通信”?；谟脩羰走x項設置。在“與繼電器通信”模式下，469PC將嘗試在啟動后立即建立通信。當處于“文件模式/默認設置”時，469PC在嘗試通信之前等待用戶單擊“打開”按鈕–當469PC在使用時沒有連接469繼電器時，首選此模式。啟動模式設置為與RS232/RS485轉換器類型匹配。如果通過469前面板RS232端口連接，請選擇“無控制類型”。如果通過GE Multilin F485轉換器單元連接，請選擇“Multilin RS232/RS485轉換器”。如果通過調制解調器連接，請選擇“調制解調器”。如果使用第三方RS232/RS485轉換器，請根據制造商的規范從可用列表中選擇適當?shù)目刂祁愋??？刂祁愋驮O(shè)置為與469 PARITY設置點匹配（參見S1 469 SETUP）。如果通過469前面板RS232端口連接，則設置為“無”。奇偶校驗設置與469 BAUD RATE（波特率）設定值匹配（參見S1 469 SETUP（設置））。波特率設置為469繼電器連接的位置（例如COM1或COM2）。在大多數計算機上，COM1由鼠標設備使用，因此COM2通常可用于通信。通信端口#本地PC上的COM端口設置為與469從屬地址設置點匹配（請參閱S1 469設置）。從屬地址3-8 469電機管理繼電器GE Multilin 3.2 469PC軟件接口3用戶界面3 3.2.4使用469PC a）將設定值保存到文件中在執行任何固件升級之前，必須將設定值存儲到本地PC上的文件中。在進行任何設定點更改或創建新的設定點文件之前，強烈建議保存設定點。要將設定值保存到本地PC上的文件中，請遵循以下步驟。1.選擇文件>屬性菜單項。出現下面的對話框，允許為469PC軟件配置正確的固件版本。469PC在創建設定點文件時需要知道正確的版本，以便特定版本中不可用的設定點不會下載到繼電器中。2.選擇正確的固件版本后，選擇文件>另存為菜單項。這將啟動以下對話框。在文件名框中輸入保存設定點的文件名，或選擇任何顯示的文件名來更新它們。
with the relay, this message will appear. 4. Click OK to edit the communications settings (or alternately, select the Communications > Computer menu item at any time). The Communications/Computer dialog box will appear containing the various communications settings for the local PC. The settings should be modified as shown below. Figure 3–3: COMMUNICATION/COMPUTER DIALOG BOX 5. To begin communications, click the ON button in the Communication section of the dialog box. The status section indicates the communications status. If communications are established, the message “469PC is now talking to a 469” is displayed. As well, the status at the bottom right hand corner of the screen indicates “Communicating”. Set the based on user preference. In “Communicate with Relay” mode, 469PC will attempt to establish communications immediately upon startup. While in the “File mode /w default settings”, 469PC waits for the user to click the ON button before attempting communications – this mode is preferred when the 469PC is being used without an attached 469 relay. Startup Mode Set to match the type of RS232/RS485 converter. If connected through the 469 front panel RS232 port, select “No Control Type”. If connected through a GE Multilin F485 converter unit, select “MULTILIN RS232/RS485 CONVERTOR”. If connected through a modem, select “Modem”. If a thirdparty RS232/RS485 converter is being used, select the appropriate control type from the available list based on the manufacturer’s specifications. Control Type Set to match the 469 PARITY setpoint (see S1 469 SETUP). If connected through the 469 front panel RS232 port, set to “None”. Parity Set to match the 469 BAUD RATE setpoint (see S1 469 SETUP). Baud Rate Set to where the 469 relay is connected (e.g. COM1 or COM2). On most computers, COM1 is used by the mouse device and as such COM2 is usually available for communications. Communcation Port # the COM port on your local PC Set to match the 469 SLAVE ADDRESS setpoint (see S1 469 SETUP). Slave Address 3-8 469 Motor Management Relay GE Multilin 3.2 469PC SOFTWARE INTERFACE 3 USER INTERFACES 3 3.2.4 USING 469PC a) SAVING SETPOINTS TO A FILE Setpoints must be saved to a file on the local PC before performing any firmware upgrades. Saving setpoints is also highly recommended before making any setpoint changes or creating new setpoint files. To save setpoints to a file on the local PC, follow the procedure below. 1. Select the File > Properties menu item. The dialog box below appears, allowing for the configuration of the 469PC software for the correct firmware version. 469PC needs to know the correct version when creating a setpoint file so that setpoints not available in a particular version are not downloaded into the relay. 2. When the correct firmware version is chosen, select the File > Save As menu item. This launches the following dialog box. Enter the filename under which the setpoints are saved in the File Name box or select any displayed file names to update them.
