HONEYWELL 51308365-175 CC-TAIX11模擬量輸入模塊
此時啟動電機是非常不可取的。在另一種情況下，電機可能驅動非常高的慣性負載。一旦電機的電源斷開，轉子可能會在減速時繼續轉動很長一段時間。電機現在變成了發電機，施加異相電源電壓可能會導致災難性故障。重啟塊功能嚴格來說是一個計時器。469不感測轉子旋轉。n重新啟動塊n[ENTER]更多重新啟動塊：關閉范圍：打開，關閉重啟塊時間：1 s范圍：1至50000 s，步進1 ENTER ESCAPE（輸入退出），信息退出注釋GE Multilin 469電機管理繼電器4-51 4 SETPOINT 4.9 S8 RTD TEMPERATURE（設置點）4 4.9S8 RTD TEMPERATURE（溫度）4.9.1 RTD TYPES PATH：設置點×S8 RTD TEMPERATURE（RTD類型）12個RTD中的每一個都可以配置為“無”或四種應用類型中的任何一種：“定子”、“軸承”、“環境”、，或“其他”。這些類型中的每一種都可能是四種不同RTD類型中的任何一種：“100歐姆鉑”、“120歐姆鎳”、“100歐姆鎳”或“10歐姆銅”。下表列出了RTD電阻與溫度的關系。n RTD類型n[ENTER]了解更多定子RTD類型：100歐姆鉑電阻范圍：100歐姆鉑金、120歐姆鎳、100歐姆鎳、10歐姆銅軸承RTD類型：10歐姆鉑電阻：100歐姆白金電阻范圍：120歐姆鎳，100歐姆鎳，10歐姆銅環境RTD類型：，10歐姆銅其他RTD類型：100歐姆鉑6路徑：設置點×S8 RTD溫度×RTD#1（6）RTD 1至6默認為“定子”RTD類型。每個RTD都有單獨的報警和跳閘配置。這允許一個RTD在故障時關閉。報警級別通常設置為略高于正常運行溫度。高報警通常設置為跳閘警告或在跳閘發生前啟動有序停機。跳閘水平通常設置在絕緣額定值。增加了跳閘表決，以確保RTD故障時的額外可靠性。如果啟用，第二個RTD也必須超過正在檢查的RTD的跳閘溫度，然后才能發出跳閘。如果選擇RTD自己投票，投票功能將被禁用。如果需要，可以更改每個RTD名稱。n RTD#1 n[ENTER]了解更多RTD#1應用：定子范圍：定子、軸承、環境、其他、無RTD#1名稱：范圍：8個字母數字字符RTD#1報警：關閉范圍：關閉、鎖定、未鎖定分配報警繼電器：報警范圍：報警、報警和輔助2、報警和Aux2和Aux3、報警和輔3、輔助2、輔助2和輔助3、，輔助3 RTD#1報警溫度：130°C范圍：1至250°C，步進1 RTD#1高報警：關閉范圍：關閉、鎖定、未鎖定的高報警繼電器：報警范圍：報警、報警和輔助2、報警和Aux2&Aux3、報警和輔助3、輔助2、Aux2&Aux3、輔助3 RTT#1高警報溫度：130℃范圍：1到250步進1 RTD#1報警事件：關閉范圍，關閉RTD#1跳閘：關閉范圍：關閉、鎖定、未鎖定RTD#1跳閘表決：RTD#1范圍：RTD#1至RTD#12分配跳閘繼電器：跳閘范圍：跳閘、跳閘和輔助2、跳閘和輔2和輔3，跳閘和輔助3 RTD#1跳閘溫度：155°C范圍：1至250°C，步進1 ENTER ESCAPE（輸入）ESCAPE?MESSAGE ESCAPE MESSAGE（退出）ESCAPE MESSAGE ESCAPE MESSURE（退出退出）4設置點4.9 S8 RTD溫度4 4.9.3 RTDS 7至10路徑：設置點？？S8 RTD溫度？？RTD#7（10）RTD 7至10默認為“軸承”RTD類型。每個RTD都有單獨的報警和跳閘配置。這允許一個RTD在故障時關閉。報警級別、高報警級別和跳閘級別通常設置為略高于正常運行溫度，但低于軸承額定溫度。增加了跳閘表決，以確保RTD故障時的額外可靠性
It would be very undesirable to start the motor at this time. In another scenario, a motor may be driving a very high inertia load. Once the supply to the motor is disconnected, the rotor may continue to turn for a long period of time as it decelerates. The motor has now become a generator and applying supply voltage out of phase may result in catastrophic failure. The Restart Block feature is strictly a timer. The 469 does not sense rotor rotation. n RESTART BLOCK n [ENTER] for more RESTART BLOCK: Off Range: On, Off RESTART BLOCK TIME: 1 s Range: 1 to 50000 s in steps of 1 ENTER ESCAPE e e MESSAGE ESCAPE NOTE GE Multilin 469 Motor Management Relay 4-51 4 SETPOINTS 4.9 S8 RTD TEMPERATURE 4 4.9S8 RTD TEMPERATURE 4.9.1 RTD TYPES PATH: SETPOINTS ?× S8 RTD TEMPERATURE ? RTD TYPES Each of the twelve RTDs may be configured as "None" or any one of four application types: "Stator", "Bearing", "Ambient", or "Other". Each of these types may in turn be any one of four different RTD types: "100 Ohm Platinum", "120 Ohm Nickel", "100 Ohm Nickel", or "10 Ohm Copper". The table below lists RTD resistance versus temperature. n RTD TYPES n [ENTER] for more STATOR RTD TYPE: 100 Ohm Platinum Range: 100 Ohm Platinum, 120 Ohm Nickel, 100 Ohm Nickel, 10 Ohm Copper BEARING RTD TYPE: 100 Ohm Platinum Range: 100 Ohm Platinum, 120 Ohm Nickel, 100 Ohm Nickel, 10 Ohm Copper AMBIENT RTD TYPE: 100 Ohm Platinum Range: 100 Ohm Platinum, 120 Ohm Nickel, 100 Ohm Nickel, 10 Ohm Copper OTHER RTD TYPE: 100 Ohm Platinum 6 PATH: SETPOINTS ?× S8 RTD TEMPERATURE ?× RTD #1(6) RTDs 1 through 6 default to "Stator" RTD type. There are individual alarm and trip configurations for each RTD. This allows one of the RTDs to be turned off if it malfunctions. The alarm level is normally set slightly above the normal running temperature. The high alarm is usually set as a warning of a trip or to initiate an orderly shutdown before tripping occurs. The trip level is normally set at the insulation rating. Trip voting has been added for extra reliability in the event of RTD malfunction. If enabled, a second RTD must also exceed the trip temperature of the RTD being checked before a trip will be issued. If the RTD is chosen to vote with itself, the voting feature is disabled. Each RTD name may be changed if desired. n RTD #1 n [ENTER] for more RTD #1 APPLICATION: Stator Range: Stator, Bearing, Ambient, Other, None RTD #1 NAME: Range: 8 alphanumeric characters RTD #1 ALARM: Off Range: Off, Latched, Unlatched ASSIGN ALARM RELAYS: Alarm Range: Alarm, Alarm & Auxiliary2, Alarm & Aux2 & Aux3, Alarm & Auxiliary3, Auxiliary2, Aux2 & Aux3, Auxiliary3 RTD #1 ALARM TEMPERATURE: 130°C Range: 1 to 250°C in steps of 1 RTD #1 HIGH ALARM: Off Range: Off, Latched, Unlatched HIGH ALARM RELAYS: Alarm Range: Alarm, Alarm & Auxiliary2, Alarm & Aux2 & Aux3, Alarm & Auxiliary3, Auxiliary2, Aux2 & Aux3, Auxiliary3 RTD #1 HIGH ALARM TEMPERATURE: 130°C Range: 1 to 250 in steps of 1 RTD #1 ALARM EVENTS: Off Range: On, Off RTD #1 TRIP: Off Range: Off, Latched, Unlatched RTD #1 TRIP VOTING: RTD #1 Range: RTD #1 to RTD #12 ASSIGN TRIP RELAYS: Trip Range: Trip, Trip & Auxiliary2, Trip & Aux2 & Aux3, Trip & Auxiliary3 RTD #1 TRIP TEMPERATURE: 155°C Range: 1 to 250°C in steps of 1 ENTER ESCAPE e e MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE GE Multilin 469 Motor Management Relay 4-53 4 SETPOINTS 4.9 S8 RTD TEMPERATURE 4 4.9.3 RTDS 7 TO 10 PATH: SETPOINTS ?× S8 RTD TEMPERATURE ?× RTD #7(10) RTDs 7 through 10 default to "Bearing" RTD type. There are individual alarm and trip configurations for each RTD. This allows one of the RTDs to be turned off if it malfunctions. The alarm level, high alarm level and the trip level are normally set slightly above the normal running temperature, but below the bearing temperature rating. Trip voting has been added for extra reliability in the event of RTD malfunction
