HIMA F8620/4處理器模塊,備件模塊
§將敏感輸入電線遠離電氣噪聲電線，如離散輸出和交流電線。這可以通過將I/O模塊分組以保持輸出模塊與敏感輸入模塊分離來實現。§每個RX3i背板的四個側面都需要10 cm（4英寸）的間隙空間，用于通風/冷卻?！霷X3i背板出于熱考慮而設計為水平安裝。其他安裝方向1 10 9 8 7 6 5 2 11 1。RX3i 2。電線槽（電線槽）3?，F(xiàn)場設備連接端子塊4。電機連接端子排5。電機起動器6。電路板7。電源8?？刂谱儔浩??？扇蹟鄶嗦菲骰驍嗦菲?0?？刂评^電器11。受保護外殼3 4圖8：系統布局指南PACSystems*RX3i系統手冊第3節GFK-2314T 2019年9月安裝21可能會影響系統性能、可靠性和機構批準，因此不建議安裝?！鞂?duì)于所有模擬模塊，包括RTD和熱電偶模塊，使用屏蔽電纜連接，屏蔽一端接地（源極）。? 2.3外殼RX3i系統及其組件被視為開放式設備[具有用戶可能接觸到的帶電電氣部件]，必須安裝在保護外殼中，或安裝在為提供安全而制造的其他組件中。外殼或組件至少應提供一定程度的保護，以防12mm以下的固體物體（例如手指）。這相當于NEMA/UL 1型外殼或IP20等級（IEC60529），提供至少2級污染環境。當RX3i系統安裝在指定為危險區域的區域時，外殼必須是只能使用工具接近的外殼。有關特定產品認證、危險區域認證類型、危險區域警告和ATEX附加外殼要求的參考，請參閱附錄A。外殼必須能夠充分消散安裝在內部的所有組件產生的熱量，以防止組件過熱。散熱也是決定是否需要風扇和空調等外殼冷卻選項的一個因素。RX3i背板的所有側面需要至少102mm（4英寸）的最小空間用于冷卻。可能需要額外的空間，這取決于設備在運行過程中產生的熱量，或取決于其他PACSystems*RX3i系統手冊第3節GFK-2314T 2019年9月安裝22的要求，如系統布線的最小彎曲半徑。附錄B說明了如何計算機柜中RX3i模塊和現場設備的散熱。2.3.1 RX3i通用背板尺寸和間距*允許冷卻通用背板前視圖側面尺寸適用于門關閉的標準模塊。側面尺寸不包括電纜和連接器所需的額外深度。帶有擴展高密度接線板（如接線板IC694TBB132）的模塊整體深約?英寸（13mm）。圖9:RX3i通用背板尺寸和間距PACSystems*RX3i系統手冊第3節GFK-2314T 2019年9月安裝23 12插槽RX3i專用背板的安裝孔與10插槽Series 90-30背板完全匹配，便于升級。背板必須水平安裝，如上所述，通過在模塊周?chē)峁┳銐虻臍饬?，以滿足產品性能和可靠性規范。其他安裝方向可能會影響系統性能、可靠性和機構批準，因此不建議使用。圖10：不建議垂直安裝2.3.2 RX3i串行擴展背板尺寸和間距每個背板都有用于安裝在電氣面板上的標準連接法蘭。PACSystems*RX3i系統手冊第3節GFK-2314T 2019年9月安裝24*冷卻余量5插槽265mm（10.43英寸）10插槽433mm（17.44英寸）5插槽250mm（9.84英寸）10槽428mm（16.85英寸）102mm*。典型的擴展背板正面圖安裝模塊的擴展背板側面圖142mm（5.59in）側面尺寸適用于門關閉的模塊。側面尺寸不包括
§ Route sensitive input wires away from electrically-noisy wires such as discrete output and AC wiring. This can be facilitated by grouping I/O modules to keep output modules separated from sensitive input modules. § Clearance space of 10 cm (4 in) on all four sides of each RX3i backplane for ventilation/cooling is required. § RX3i backplanes are designed to be mounted horizontally due to thermal considerations. Other mounting orientations 1 10 9 8 7 6 5 2 11 1. RX3i 2. Wireway (Wire Duct) 3. Field device connection terminal block 4. Motor connection terminal block 5. Motor starters 6. Circuit board 7. Power supply 8. Control transformer 9. Fusible disconnect or circuit breaker 10. Control relays 11. Protected enclosure 3 4 Figure 8: System Layout Guidelines PACSystems* RX3i System Manual Section 3 GFK-2314T Sept. 2019 Installation 21 may affect system performance, reliability, and agency approvals, and are therefore not recommended. § Use shielded cable connections with the shield grounded at one end (at source) for all analog modules, including RTD and Thermocouple modules. ? 2.3 Enclosures The RX3i system and its components are considered open equipment [having live electrical parts that may be accessible to users] and must be installed in a protective enclosure or incorporated into other assemblies manufactured to provide safety. At a minimum, the enclosure or assemblies shall provide a degree of protection against solid objects up to 12mm (e.g. fingers). This equates to a NEMA/UL Type 1 enclosure or an IP20 rating (IEC60529) providing at least a pollution degree 2 environment. When an RX3i system is installed into an area designated as a Hazardous Area, then the enclosure must be one that is only accessible by use of a tool. Refer to Appendix A for reference to specific product certifications, types of Hazardous Area approvals, Hazardous Area warnings, and additional enclosure requirements with respect to ATEX. The enclosure must be able to adequately dissipate the heat generated by all of the components mounted inside so that no components overheat. Heat dissipation is also a factor in determining the need for enclosure cooling options such as fans and air conditioning. A minimum space of at least 102 mm (4 in) is required on all sides of the RX3i backplane for cooling. Additional space may be required, depending on the amount of heat generated by the equipment during operation, or on other PACSystems* RX3i System Manual Section 3 GFK-2314T Sept. 2019 Installation 22 requirements such as minimum bend radius for system cabling. Appendix B explains how to calculate heat dissipation for RX3i modules and field devices in an enclosure. 2.3.1 RX3i Universal Backplane Dimensions and Spacing * Allowance for cooling Universal Backplane front view Side dimension is for standard modules with doors closed. Side dimension does not include extra depth required for cables and connectors. Modules with Extended High-Density Terminal Blocks (such as Terminal Block IC694TBB132) are approximately ?-inch (13mm) deeper overall. Figure 9: RX3i Universal Backplane Dimensions and Spacing PACSystems* RX3i System Manual Section 3 GFK-2314T Sept. 2019 Installation 23 The mounting holes for the 12-slot RX3i Universal Backplane match the 10-slot Series 90-30 Backplane exactly, for easy upgrades. Backplanes must be mounted horizontally, as represented above, to meet product performance and reliability specifications by providing adequate airflow around the modules. Other mounting orientations may affect system performance, reliability and agency approvals, and are therefore not recommended. Figure 10: Vertical Mounting Not Recommended 2.3.2 RX3i Serial Expansion Backplane Dimensions and Spacing Each backplane has standard attachment flanges for mounting on an electrical panel. PACSystems* RX3i System Manual Section 3 GFK-2314T Sept. 2019 Installation 24 * Allowance for cooling 5-Slot 265mm (10.43in) 10-Slot 433mm (17.44in) 5-Slot 250mm (9.84in) 10-Slot 428mm (16.85in) 102mm * (4.00in) 102mm * (4.00in) 102mm * (4.00in) 90mm (3.54in) 20mm (0.79in) 130mm (5.12in) 102mm * (4.00in) 5.08mm 0.20 dia. typical Expansion Backplane front view Expansion Backplane with modules installed side view 142mm (5.59in) Side dimension is for modules with doors closed. Side dimension does not include extra depth required for
