HIMA F3211A系統模塊卡件
值參考地址。每個信道占用2個字，無論是否使用信道：根據其配置的信道值格式，每個啟用的信道向CPU報告32位浮點或16位整數值。在16位整數模式中，32位通道數據區的低位字包含16位整數通道值。32位值的高位字（高位16位）設置為16位整數的符號擴展。此符號擴展的高位字允許16位整數在邏輯中讀取為32位整數類型，而不會丟失PACSystems*RX3i系統手冊第10節GFK-2314T 2019年9月模擬輸入模塊405的整數符號。如果16位整數結果為負，則32位通道數據中的高位字具有值0xFFFF。如果16位整數結果為正，則高位字為0x0000。16位分辨率模塊模擬輸入數據以16位2的補碼格式存儲在CPU中，如下圖所示。MSB LSB 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 PACSystems*RX3i系統手冊第10節GFK-2314T 2019年9月模擬輸入模塊406 9.9.5.7通道診斷數據：ALG233除了來自現場設備的輸入數據外，該模塊可以被配置為向CPU報告信道診斷狀態數據。CPU將此數據存儲在為模塊配置的診斷參考地址中。此功能的使用是可選的。每個通道的診斷數據占用兩個字（無論是否使用通道）：當診斷位等于1時，通道上出現報警或故障狀態。當位等于0時，報警或故障條件不存在，或者該通道的配置中未啟用檢測。對于每個通道，該數據的格式為：9.9.6現場接線：ALG233端子連接1用戶提供24V輸入；通過24VOUT端子（引腳2）2+24V回路電源連接點3電流輸入提供回路電源，PACSystems*RX3i系統手冊第10節GFK-2314T 2019年9月模擬輸入模塊4099.10模擬輸入模塊8-/4通道電流/電壓：IC695ALG608模擬輸入模塊16-/8通道電流/電流：IC695ALG616 IC695ALD616 I1 I2 I4 I5 16 I7 18 19 I10 I11 I12 I13 I14 I16模塊OK現場狀態TB圖285:IC695ALL616非隔離差分模擬輸入電流/電壓模塊IC695ALG608提供八個單端或四個差分輸入通道。非隔離差分模擬輸入電流/電壓模塊IC695ALG616（圖285）提供16個單端或8個差分輸入通道。模擬輸入通道可用于以下范圍：? 電流：0至20mA、4至20mA、±20mA? 電壓：±10 Vdc、0至10 Vdc、±5 Vdc、0到5 Vdc、1Vdc到5 Vdc。Value Reference Address. Each channel occupies 2 words, whether or not the channel is used: Depending on its configured Channel Value Format, each enabled channel reports a 32-bit floating-point or 16-bit integer value to the CPU. In the 16-bit integer mode, the low word of the 32-bit channel data area contains the 16-bit integer channel value. The high word (upper 16-bits) of the 32-bit value is set with the sign extension of the 16-bit integer. This sign-extended upper word allows the 16-bit integer to be read as a 32-bit integer type in logic without PACSystems* RX3i System Manual Section 10 GFK-2314T Sept. 2019 Analog Input Modules 405 losing the sign of the integer. If the 16-bit integer result is negative, the upper word in the 32-bit channel data has the value 0xFFFF. If the 16-bit integer result is positive, the upper word is 0x0000. The 16-bit resolution module analog input data is stored in the CPU in 16-bit 2’s complement format as displayed in the following figure. MSB LSB 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 PACSystems* RX3i System Manual Section 10 GFK-2314T Sept. 2019 Analog Input Modules 406 9.9.5.7 Channel Diagnostic Data: ALG233 In addition to the input data from field devices, the module can be configured to report channel diagnostics status data to the CPU. The CPU stores this data at the Diagnostic Reference Address configured for the module. Use of this feature is optional. The diagnostics data for each channel occupies two words (whether the channel is used or not): When a diagnostic bit equals 1, the alarm or fault condition is present on the channel. When a bit equals 0 the alarm or fault condition is either not present or detection is not enabled in the configuration for that channel. For each channel, the format of this data is: 9.9.6 Field Wiring: ALG233 Terminal Connection 1 User supplied 24V Input; provides loop power via 24VOUT terminal (pin 2) 2 +24V loop power tie point 3 Current Input, PACSystems* RX3i System Manual Section 10 GFK-2314T Sept. 2019 Analog Input Modules 409 9.10 Analog Input Module 8-/4-Channel Current/Voltage: IC695ALG608 Analog Input Module 16-/8-Channel Current/Voltage: IC695ALG616 IC695ALG616 I1 I2 I3 I4 I5 16 I7 18 19 I10 I11 I12 I13 I14 I15 I16 MODULE OK FIELD STATUS TB Figure 285: IC695ALG616 Non-Isolated Differential Analog Input Current/Voltage module IC695ALG608 provides eight single-ended or four differential input channels. Non-Isolated Differential Analog Input Current/Voltage module IC695ALG616, (Figure 285) provides 16 single-ended or 8 differential input channels. Analog input channels can be configured for these ranges: ? Current: 0 to 20mA, 4 to 20mA, ±20mA ? Voltage: ±10 Vdc, 0 to 10 Vdc, ±5Vdc, 0 to 5Vdc, 1Vdc to 5Vdc.
