HIMA F1101 DCS模塊卡件
和低報警? 上夾具和下夾具? 超量程和欠量程報警每個報警可按通道單獨配置，以生成診斷位狀態、故障報警或中斷報警。PACSystems*RX3i系統手冊第12節GFK-2314T 2019年9月模擬輸出模塊461如果命令信道高于上限值，則輸出設置為上限值，并指示上限條件。如果命令通道低于下限值，則輸出設置為下限值，并指示下限條件。在可能通過斜坡、箝位和故障條件進行調整后，對工程單位輸出值執行高報警和低報警檢查。PACSystems*RX3i系統手冊第12節GFK-2314T 2019年9月模擬輸出模塊462信道參數（續）參數默認說明診斷報告啟用如果啟用了診斷報告，則可以使用下面列出的其他參數啟用特定類型的報警。Disabled Diagnostic Reporting Enable（禁用診斷報告啟用）選項用于啟用將報警報告到Diagnostic reference（診斷參考）區域的參考內存。故障報告啟用選項可將報警記錄到I/O故障表中。這些參數啟用或禁用通道的各個診斷功能。當這些參數中的任何一個被啟用時，模塊使用相關參數來執行啟用的功能。例如，如果在Diagnostic Reporting Enable（診斷報告啟用）菜單中啟用了Over Range（超出范圍），則模塊將在通道的Diagnostic Reference（診斷參考）中設置Over Range位。如果這些參數中的任何一個被禁用，則模塊不會對相關報警條件做出反應。例如，如果在故障報告啟用菜單中將低報警啟用設置為禁用，則當通道上檢測到低報警時，低報警故障不會記錄在I/O故障表中。故障報告啟用如果啟用了故障報告，下面列出的其他參數可用于啟用特定類型的故障。禁用中斷啟用禁用低報警啟用禁用高報警啟用禁用低范圍啟用禁用超范圍啟用禁用下限報警啟用禁用上限報警啟用禁用PACSystems*RX3i系統手冊第12節GFK-2314T 2019年9月模擬輸出模塊463 10.3.13.3.1報警和故障報告診斷報告啟用、故障報告啟用、，和中斷啟用配置參數可用于啟用各個信道報警的不同類型的響應。默認情況下，在每個通道上禁用所有響應?？梢詾槊總€(gè)通道配置報警啟用的任何組合。? 如果啟用了診斷報告，模塊將在為該通道配置的診斷參考地址的參考存儲器中報告通道報警。? 如果啟用了故障報告，則模塊會在I/O故障表中記錄每次通道報警的故障日志。? 如果啟用了中斷，警報可以觸發應用程序中中斷塊的執行，如下所述。10.3.13.3.2使用中斷要正確配置I/O中斷，必須在該模塊的配置文件中設置中斷啟用位。此外，應響應信道中斷而執行的程序塊必須映射到對應于該信道的參考地址。示例：在此示例中，輸出參考地址塊映射到%AQ0001-%AQ0008。
and Low Alarm ? Upper Clamp and Lower Clamp ? Over-range and Under-range Alarm Each alarm is individually configurable per channel to generate diagnostics bit status, fault alarms, or interrupt alarms. PACSystems* RX3i System Manual Section 12 GFK-2314T Sept. 2019 Analog Output Modules 461 If a channel is commanded higher than the Upper Clamp value, the output is set to the Upper Clamp value and an Upper Clamp condition is indicated. If a channel is commanded lower than the Lower Clamp value, the output is set to the Lower Clamp value and a Lower Clamp condition is indicated. The High and Low Alarm checks are performed on the engineering units output value after possibly being adjusted by ramping, clamping, and fault conditions. PACSystems* RX3i System Manual Section 12 GFK-2314T Sept. 2019 Analog Output Modules 462 Channel Parameters (Continued) Parameter Default Description Diagnostic Reporting Enable If Diagnostic Reporting is enabled, the additional parameters listed below can be used to enable specific types of alarms. Disabled Diagnostic Reporting Enable options are used to enable reference memory reporting of alarms into the Diagnostic Reference area. Fault Reporting Enable options enable fault logging of alarms into the I/O Fault Table. These parameters enable or disable the individual diagnostics features of a channel. When any of these parameters is enabled, the module uses associated parameters to perform the enabled feature. For example, if Over Range is enabled in the Diagnostic Reporting Enable menu, the module will set the Over Range bit in the Diagnostic Reference for the channel. If any of these parameters is disabled, the module does not react to the associated alarm conditions. For example, if Low Alarm Enable is set to Disabled in the Fault Reporting Enable menu, the Low Alarm fault is not logged in the I/O Fault Table when Low Alarm is detected on the channel. Fault Reporting Enable If Fault Reporting is enabled, the additional parameters listed below can be used to enable specific types of Faults. Disabled Interrupts Enable Disabled Low Alarm Enable Disabled High Alarm Enable Disabled Under Range Enable Disabled Over Range Enable Disabled Lower Clamp Alarm Enable Disabled Upper Clamp Alarm Enable Disabled PACSystems* RX3i System Manual Section 12 GFK-2314T Sept. 2019 Analog Output Modules 463 10.3.13.3.1 Alarming and Fault Reporting The Diagnostic Reporting Enable, Fault Reporting Enable, and Interrupt Enable configuration parameters can be used to enable different types of responses for individual channel alarms. By default, all responses are disabled on every channel. Any combination of alarm enables can be configured for each channel. ? If Diagnostic Reporting is enabled, the module reports channel alarms in reference memory at the Diagnostic Reference address configured for that channel. ? If Fault Reporting is enabled, the module logs a fault log in the I/O Fault table for each occurrence of a channel alarm. ? If Interrupts are enabled, an alarm can trigger execution of an Interrupt Block in the application program, as explained below. 10.3.13.3.2 Using Interrupts To properly configure an I/O Interrupt, the Interrupt enable bit or bits must be set in the configuration profile of this module. In addition, the program block that should be executed in response to the channel interrupt must be mapped to the reference address corresponding to that channel. Example: In this example, the Output Reference Address block is mapped to %AQ0001-%AQ0008.
