EMERSON 1C31125G01 DCS卡
SEEPROM地址開關，S1一個4位SMT配置開關位于MVME7216E轉換模塊上，用于設置RTM串行EEPROM設備的設備地址。下表“后面板連接器”中定義了開關設置。MVME7216E轉換模塊提供了這些連接器。所有連接器均使用符合VME總線規范的標準引腳分配。PIM I/O（PIM）連接器J10僅從VME P2連接器布線電源和接地。此連接器上沒有主機I/O信號。MVME7100將PMC I/O從PMC插槽1的J14路由到VME P2的A和C行。MVME7216E將這些信號（針對針）從VME P2路由到PMC I/O模塊連接器J14。ACT活動或以太網或千兆E以太網連接器速度10/100/1000Mb/s以太網連接器有兩組ACT和SPEED LED，每個以太網連接器一組。下表對其進行了描述。VME7216E PMC I/O模塊（PIM）連接器（J10、J14）PMC主機I/O連接器J10僅從VME P2路由電源和接地。此連接器上沒有主機I/O信號。MVME7100將PMC I/O從PMC插槽1的J14路由至VME P2 A和C行。MVME7216E將這些信號（針對針）從VME P2路由至PMC I/O模塊連接器J14。引腳分配見表5-6和表3-8。
SEEPROM Address Switch, S1 A 4-position SMT configuration switch is located on the MVME7216E transition module to set the device address of the RTM serial EEPROM device. The switch settings are defined in the next table Rear Panel Connectors The MVME7216E transition module provides these connectors. All connectors use standard pin assignments in compliance with the VMEbus specifications.PMC I/O (PIM) connector J10 routes only power and ground from VME P2 connector. There are no host I/O signals on this connector. The MVME7100 routes PMC I/O from J14 of PMC Slot 1 to VME P2 rows A and C. The MVME7216E routes these signals (pin-for-pin) from VME P2 to PMC I/O module connector J14.ACT Activity or Ethernet or Gigabit E Ethernet connector SPEED 10/100/1000Mb/s of Ethernet connectors There are two sets of ACT and SPEED LEDs, one set for each Ethernet connector. They are described in the next table.MVME7216E PMC I/O Module (PIM) Connectors (J10, J14) PMC host I/O connector J10 routes only power and ground from VME P2. There are no host I/O signals on this connector. The MVME7100 routes PMC I/O from J14 of PMC Slot 1 to VME P2 rows A and C. The MVME7216E routes these signals (pin-for-pin) from VME P2 to PMC I/O Module connector J14. See Table 5-6 and Table 3-8 for the pin assignments.
