REXROTH MKD090B-047-KG1KN伺服電機
1.產 品 介 紹
品牌：REXROTH
型號說明：REXROTH MKD090B-047-KG1KN伺服電機
優勢：供應進口原裝正品，專業停產配件。
公司主營特點：主營產品各種模塊/卡件，控制器，觸摸屏，伺服驅動器。
2.產 品 詳 情 資 料：
REXROTH MKD090B-047-KG1KN這些規范要求卡導向器底部（相鄰導向器之間）的材料高度不超過0.236英寸。不得超過卡導軌的最大材料條件，以適應上述配置中填充有IP的MVME162-4xx板。MVME162FX上的IP安裝REXROTH MKD090B-047-KG1KNEmbedded Controller上最多可安裝四個IndustryPack（IP）模塊。按以下步驟在控制器上安裝IP：1。每個IP有兩個50針接頭，可插入控制器上兩個相應的50針接頭：J2/J3、J7/J8、J13/J14、J18/J19。連接器位置見圖2-1調整儀表板的方向，使錐形連接器外殼正確配合。將IP_a插入接頭J2和J3；將IP_b插入J7和J8。將IP_c插入J13和J14；將IP_d插入J18和J19。如果使用雙倍大小的IP，請將IP_ab插入J2、J3、J7和J8；將IP_cd插入J13、J14、J18和J19。REXROTH MKD090B-047-KG1KN
These specifications require that the height of the material at the card guide base (between adjacent guides), does not exceed 0.236 inches. This maximum material condition for the card guides must not be exceeded in order to accommodate an REXROTH MKD090B-047-KG1KNboard populated with IPs in the configuration described above. IP Installation on the MVME162FX Up to four IndustryPack (IP) modules may be installed on the MVME162FX Embedded Controller. Install the IPs on the controller as follows: 1. Each IP has two 50-pin connectors that plug into two corresponding 50-pin connectors on the controller: J2/J3, J7/J8, J13/J14, J18/J19. See Figure 2-1 for connector locations. – Orient the IP(s) so that the tapered connector shells mate properly. Plug IP_a into connectors J2 and J3; plug IP_b into J7 and J8. Plug IP_c into J13 and J14; plug IP_d into J18 and J19. If a double-sized IP is used, plug IP_ab into J2, J3, J7, and J8; plug IP_cd into J13, J14, J18, and J19.REXROTH MKD090B-047-KG1KN
3.產 品 展 示
4.公 司 優 勢 主 營 產 品
5.相 關 產 品 展 示
本篇文章出自瑞昌明盛自動化設備有限公司官網，轉載請附上此鏈接:http://qing-ting.cn
