REXROTH HMD01.1N-W0020-A-07-NNNN調節閥
1.產 品 介 紹
品牌：REXROTH
型號說明：REXROTH HMD01.1N-W0020-A-07-NNNN調節閥
優勢：供應進口原裝正品，專業停產配件。
公司主營特點：主營產品各種模塊/卡件，控制器，觸摸屏，伺服驅動器。
2.產 品 詳 情 資 料：
REXROTH HMD01.1N-W0020-A-07-NNNN這些可讀跳線可以作為存儲器控制器（MC2芯片）ASIC上的寄存器（$FFF4202D）讀取。當跳線斷開時，位值讀取為1，當跳線接通時，位讀取為0。此跳線塊（標頭J22）包含8位。有關MC2芯片的更多信息，請參閱《REXROTH HMD01.1N-W0020-A-07-NNNN嵌入式控制器程序員參考指南》。REXROTH HMD01.1N-W0020-A-07-NNNNBug保留/定義四個低階位（GPI3至GPI0）。以下是調試器保留/定義的位的描述：Bit J22 Pins description Bit#0（GPI0）15-16當設置為1（高）時，指示調試器將本地靜態RAM用于其工作頁（即變量、堆棧、矢量表等）。當設置為0（高），指示調試器使用Flash或PROM中的默認設置/操作參數與NVRAM中的用戶設置/操作。這與同時按下RESET和ABORT開關相同
These readable jumpers can be read as a register (at $FFF4202D) on the Memory Controller (MC2 chip) ASIC. The bit values are read as a one when the jumper is off, and as a zero when the jumper is on. This jumper block (header J22) contains eight bits. Refer also to theREXROTH HMD01.1N-W0020-A-07-NNNNEmbedded Controller Programmer’s Reference Guide for additional information on the MC2 chip. The MVME162Bug reserves/defines the four lower order bits (GPI3 to GPI0). The following is the description for the bits reserved/defined by the debugger: Bit J22 Pins Description Bit #0 (GPI0) 15-16 When set to 1 (high), instructs the debugger to use local Static RAM for its work page (i.e., variables, stack, vector tables, etc.).When set to 1 (high), instructs the debugger to use the default setup/operation parameters in Flash or PROM versus the user setup/operation parameters in NVRAM. This is the same as depressing the RESET and ABORT switches at the same time.REXROTH HMD01.1N-W0020-A-07-NNNN
3.產 品 展 示
4.公 司 優 勢 主 營 產 品
5.相 關 產 品 展 示
本篇文章出自瑞昌明盛自動化設備有限公司官網，轉載請附上此鏈接:http://qing-ting.cn
