NI PXI-4472通道聲音振動板
1.產 品 介 紹
品牌：NI
型號說明：NI PXI-4472通道聲音振動板
優勢：供應進口原裝正品，專業停產配件。
公司主營特點：主營產品各種模塊/卡件，控制器，觸摸屏，伺服驅動器。
2.產 品 詳 情 資 料：
安裝主總線300接口NI PXI-4472由處理器單元通過CEX總線供電，因此不需要額外的外部電源。底板TP853提供兩個以太網端口，用于連接MasterBus 300的冗余以太網網絡。使用以下步驟安裝CI855/TP853:1。將裝置安裝在DIN導軌上，請參見第65頁的“將AC 800M裝置安裝到DIN導軌上”和第78頁的“以單一配置安裝NI PXI-4472處理器裝置”。2.將以太網雙絞線連接到基板上的觸點。3.將以太網電纜的另一端連接到以太網交換機。以太網雙絞線連接以太網雙絞線通過位于NI PXI-4472上的10BaseT RJ45連接器連接。有關連接器的說明，請參見第84頁的表5。如果需要AUI接口，則需要從10BaseT到AUI的轉換器。通信單元CI855不能向收發器供電，因此必須使用單獨的電源。請注意，CI855單元沒有單元冗余。NI PXI-4472
Installing the MasterBus 300 Interface,NI PXI-4472is powered from the processor unit via the CEX-Bus and requires therefore no additional external power source. The baseplate, TP853, provides two Ethernet ports for connection of redundant Ethernet network for MasterBus 300. Use the following procedure to install the CI855/TP853: 1. Mount the unit on the DIN-rail, see Mounting AC 800M Units onto DIN-Rail on page 65 and Installing the NI PXI-4472 Processor Unit in Single Configuration on page 78. 2. Connect the Ethernet twisted pair cable to the contact on the baseplate. 3. Connect the other end of the Ethernet cable to an Ethernet Switch. Ethernet twisted pair Connection The Ethernet twisted pair is connected via the 10BaseT RJ45 connector located onNI PXI-4472. For a description of the connector, see Table 5 on page 84. If an interface to an AUI is required, a converter from 10BaseT to AUI is needed. The communication unit, CI855, can not provide power to the transceiver, therefore a separate power source must be used. Note that there is no unit redundancy for the CI855 unit.
3.產 品 展 示
4.公 司 優 勢 主 營 產 品
5.相 關 產 品 展 示
本篇文章出自瑞昌明盛自動化設備有限公司官網，轉載請附上此鏈接:http://qing-ting.cn
