ABB SDCS-DSL-4-SET DCS系統模塊
1.產 品 資 料 介 紹：
中文資料：
ABB SDCS-DSL-4-SET邏輯校驗和字每次掃描要用作校驗和算法輸入的用戶邏輯字的數量。有效范圍：0到32760，增量為8。默認值：16?？刂破魍ㄐ糯翱谀Ｊ剑▋H當掃描模式設置為正常時可用。）控制器通信窗口的執行設置。選擇：? 完成：窗口運行到完成。沒有時間限制。? ABB SDCS-DSL-4-SET有限：時間限制。每次掃描的控制器通信窗口的最大執行時間在控制器ABB SDCS-DSL-4-SET通信窗口計時器參數中指定。默認值：有限。注：此參數對應于90-70系列PLC上的編程器窗口模式參數。ABB SDCS-DSL-4-SET
ABB SDCS-DSL-4-SET控制器通信窗口計時器（ms）（僅當掃描模式設置為正常時可用。僅當控制器通信窗口模式設置為完成時讀取。）每次掃描控制器通信窗口的最大執行時間。此值不能大于看門狗計時器的值。
有效范圍和默認值取決于控制器通信窗口模式：? 完成：沒有時間限制。? 有限：有效范圍：0到255ms。默認值：10。注：此參數對應于90-70系列PLC上的編程器窗口定時器參數
英文資料：
ABB SDCS-DSL-4-SETLogic Checksum Words The number of user logic words to use as input to the checksum algorithm each sweep. Valid range: 0 through 32760, in increments of 8. Default: 16. Controller Communication Window Mode (Available only when Sweep Mode is set to Normal.) Execution settings for the Controller Communications Window. Choices: ? Complete: The window runs to completion. There is no time limit. ? Limited: Time sliced. ABB SDCS-DSL-4-SETThe maximum execution time for the Controller Communications Window per scan is specified in the Controller Communications Window Timer parameter. Default: Limited. Note: This parameter corresponds to the Programmer Window Mode parameter on a Series 90-70 PLC.ABB SDCS-DSL-4-SET
ABB SDCS-DSL-4-SETController Communications Window Timer (ms) (Available only when Sweep Mode is set to Normal. Read-only if the Controller Communications Window Mode is set to Complete.) The maximum execution time for the Controller Communications Window per scan. This value cannot be greater than the value for the watchdog timer.ABB SDCS-DSL-4-SET
ABB SDCS-DSL-4-SETThe valid range and default value depend on the Controller Communications Window Mode: ? Complete: There is no time limit. ? Limited: Valid range: 0 through 255ms. Default: 10. Note: This parameter corresponds to the Programmer Window Timer parameter on a Series 90-70 PLC
2.產 品 展 示
3.主 營 品 牌
本篇文章出自瑞昌明盛自動化設備有限公司官網，轉載請附上此鏈接:http://qing-ting.cn
